Header Ads

Seo Services

Fix Windows Error Code 1 Not Configured Correctly in Windows 10

If you're getting the Windows code 1 problem, it implies that one of your system's devices isn't working properly.


The Device Manager is a built-in Windows service that hosts and displays all of the system's installed device drivers. It is the most important location in the system for seeing the current condition of all system driver software as well as dealing with any driver-related issues or abnormalities.


Fix Windows Error Code 1 Not Configured Correctly in Windows 10


If drivers are missing, corrupted, or damaged, the defective driver will be shown in the Device Manager window, and users may utilize the Device Manager to try to rectify the error.


So, let's attempt to find out what error code 1 is and how to fix the "device is not configured" issue with the help of this blog.


What is the meaning of error code 1


When you get a Windows code 1 error, it means that some of the device drivers on your Windows 10 system aren't configured correctly. The Device Manager is largely to blame for this problem.


The major significance of this issue is that either the system does not have the right drivers installed or the driver software is not set appropriately. This might lead to system failure, thus it has to be addressed immediately.


Error code of windows service manager 1

When the driver software is missing or poorly set, the Windows code 1 error is a foregone conclusion, which may be validated in the following manner.


  • Go to the Device Manager tab.
  • To find out which device driver is missing or damaged, expand each category.
  • You may right-click on the device to open its Properties window once it has been discovered (typically denoted by a yellow exclamation point).
  • The problem code will be shown in the Device Status section of the General tab of the Properties window.
  • When you read the error notice "Code-1" you know that the device isn't set correctly, and you can figure out how to solve it.


How to Fix Error Code 1 on a Windows System:


In this post, we'll look at how to repair the "device not configured" issue.


The first fix is to update the device drivers.


If you get a Windows code 1 problem, the first and most important thing you should do is update the malfunctioning device driver software. This may be able to resolve the issue with your Windows PC and allow you to run the device without problems.


Manually Update Faulty Drivers Using Device Manager


  • After identifying the problematic driver in Device Manager, right-click on it to access the context menu.
  • Then, from the drop-down menu, pick the “Update driver” option.


Fix Windows Error Code 1 Not Configured Correctly in Windows 10


  • Then, from the following window, choose “Search automatically for updated driver software.”


Fix Windows Error Code 1 Not Configured Correctly in Windows 10

  • To finish the driver software update procedure, keep following the on-screen directions.
  • To save and implement the changes, restart your computer.

Automatically Update Faulty Drivers


If you don't have enough time to update the drivers as described above, you may download a fully free driver updater application and use it to install the newest drivers for the problematic devices on your system.


Fix 2: Remove and reinstall the corrupted driver


With the Device Manager program, you may attempt removing and reinstalling the defective device driver to fix the Windows code 1 problem.


  • Open the Device Manager windows to do so.
  • Then, from the context menu, right-click on the defective driver software's name and select "Uninstall."


Fix Windows Error Code 1 Not Configured Correctly in Windows 10


  • When the prompt appears, confirm your action by clicking "OK" and check the box that reads "Delete the device's driver software."
  • After the uninstallation procedure is complete, go to the manufacturer's website to reinstall the device on your computer.
  • If you want, you may use the Action button to scan for hardware changes and then download the gadget from the manufacturer's website.


Fix Windows Error Code 1 Not Configured Correctly in Windows 10


  • Finally, restart your computer to save and implement your modifications.


Solution 3: Make use of the Registry Editor


When connecting USB devices to your PC, you may get the “This device is not configured” error. You can use the Registry Editor to solve this problem and fix this bug. To solve this problem, you must delete the Upperfilters and Lowerfilters keys, which may be done in the following way:


  • Click the "OK" button after typing "Regedit" in the input field in the Run dialogue box. (Click "Yes" if the User Action Control asks for permission.)
  • Then go to the Registry Editor by following the steps below: Computer\HKEY LOCAL MACHINE\SYSTEM\CurrentControlSet\Control\Class\{36FC9E60-C465-11CF-8056-444553540000}
  • To remove the Upperfilters key and the Lowerfilters keys option, go to the right-hand side pane of the Registry Editor window.


Fix Windows Error Code 1 Not Configured Correctly in Windows 10

  • If provided with a permission-seeking option, select "OK."
  • Finally, restart the computer to save and activate the modifications.

This should fix the code 1 problem on your Windows 10 system caused by an improperly configured device.


Fix 4: Restore your computer to a previous state


If nothing else works, you can restore your system to a point before you started getting the Windows code 1 problem.


If you've recently installed or uninstalled apps, this could result in the "device is not configured" error. In this case, you can use the steps below to restore your system to a point before the error occurred.


  1. Start the Run dialogue box and type "rstrui" then press the "OK" button.
  2. To access the PC's Restore points, click Next when the System Restore dialogue appears.
  3. Select the most recent point and then select the Next option.
  4. Additionally, click Finish to begin the restoration of your Windows PC.


Fix Windows Error Code 1 Not Configured Correctly in Windows 10


Error Code 1: Device Not Configured is been fixed in Windows.


So that's everything there is to know about the Windows code 1 issue and how to fix it. Updating device drivers via the automated approach or using Device Manager may be able to remedy the problem.


You may also try rebooting the machine once since this has been known to resolve certain transient problems and system malfunctions.



Summary

The error codes issued by Device Manager in Windows are covered in this article. You've presumably come to this page because Device Manager or another tool, such as DXDiag, has given you an error code and you're not sure how to fix it. In this post, we'll show you how to identify your problem code and offer suggestions on how to fix it.


HTTP status codes


First, try these steps.

To start, consider one of the following typical ways to fix the problem:


Run a troubleshooter on Windows 7 and 8.1.


For Windows 7 and 8.1: Locate and resolve device and hardware issues.


For Windows 10, read the section below titled "Update the device driver."


The device driver should be updated.


Windows Update may be used to update the device driver.


Windows Update may be used to update the device driver for the hardware.


The device driver was updated from the vendor's website.


The device driver may be downloaded from the vendor's website. Follow the instructions for installing or updating their software.


  1. Visit the manufacturer's website if the device was preloaded on the PC.
  2. Visit the device manufacturer's website if the device was installed after the computer was purchased.
  3. Visit the device maker's website if the device was preloaded on the computer and the computer manufacturer does not have an updated driver for the device.


Note: Make that the device drivers you're installing are compatible with the Windows version and platform you're using.



Device Manager error codes


If the preceding procedures failed to fix your problem or were unavailable, look up your error code in the table below and follow the recommended remedies for that error code. You may also click on a specific error code to learn more about it.


Note: This article does not cover all of the trouble codes that Device Manager generates. If you're experiencing an error code that isn't listed here, you can seek assistance from the hardware device manufacturer's technical support or Microsoft Support.


In Device Manager, where do you look for your problem code


  1. Double-click the device type that is causing the issue in Device Manager.
  2. Right-click the device that is causing the issue, then choose Properties. This brings up the device's Properties window. The problem code is displayed in the Device status section of this dialogue box.


Error Codes and How to Fix Them


1 (code) "This device is not set up properly. (code 1) "


The reason for the error code 1


Your computer does not have any drivers for the device, or the drivers are set improperly.


Resolution Suggestions


  • Install the most recent driver


Click the Driver tab in the device's Properties dialogue box, then Update Driver to launch the Hardware Update Wizard. To update the driver, follow the on-screen instructions. If upgrading the driver does not solve the problem, see the documentation that came with your hardware.


Note: You may be asked to provide the driver's path. Windows may have the driver built-in, or the driver files from the last time you set up the device may still be installed. If you don't have the driver and are asked for it, try downloading the most recent version from the hardware vendor's website.


Code 3: “This device's driver may be corrupted

Message in its entirety


“Your system may be running low on memory or other resources, or the driver for this device may be corrupted. (Code 3)”


Cause


The device driver might be faulty, or you could be out of memory; the system may need to free up or add extra memory.


Recommendations for Action


Close several apps that are currently open.


If the computer's memory is inadequate to operate the device, you can shut certain programs to free up space. You may also examine the virtual memory settings, as well as memory and system resources.


  • Open Task Manager to examine memory and system resources. To do so, press CTRL+ALT+DELETE, then select Task Manager from the menu.
  • Open the System Properties dialogue box, choose the Advanced tab, and then click Settings in the Performance section to verify virtual memory settings.


The driver should be uninstalled and reinstalled.


The device driver may have gotten corrupted. Remove the driver from Device Manager and reinstall it by scanning for new devices.


  1. Click the Driver tab in the device's Properties dialogue box, then Uninstall. Pay attention to the directions.
  2. Your computer should be restarted.
  3. To check for hardware changes, open Device Manager, select Action and then Scan for Hardware Changes. Pay attention to the directions.


Note You may be asked to provide the driver's path. Windows may have the driver built-in, or the driver files from the last time you set up the device may still be installed. However, it may occasionally launch the New Hardware Wizard, which may prompt you for the driver. If you don't have the driver and are asked for it, try downloading the most recent version from the hardware vendor's website.


Additional RAM should be installed.


You may need to install

It's possible that you'll need to add more random access memory (RAM).


“Windows is unable to recognize this hardware... (9-digit code)”

Message in its entirety


"Windows is unable to recognize this device because it lacks a proper hardware identification number. Contact the hardware manufacturer for assistance. (Number 9)"


The reason for the error code 9


Your PC has detected invalid device IDs for your hardware.


Recommendations for Action


Make contact with the hardware provider. It's either the hardware or the driver that's broken.


Code ten "This gadget will not turn on. (Problem 10)"

Error Message in Its Entirety


"This gadget will not turn on. Upgrade the device drivers for this device if necessary. (Problem 10)"


The reason for the error code 10


A "FailReasonString" value is often found in the device's hardware key, and the value string shows an error message set by the hardware manufacturer. The message above is displayed if the hardware key does not have a “FailReasonString” value.


this device cannot start. (code 10) usb flash drive windows 7


Resolutions that are suggested

Drivers must be updated.


Click the Driver tab in the device's Properties dialogue box, then Update Driver to launch the Hardware Update Wizard. To update the driver, follow the on-screen instructions.


Note that you may be asked to provide the driver's path.


Note You may be asked to provide the driver's path. If you don't have the driver and are asked for it, try downloading the most recent version from the hardware vendor's website.


"This device is unable to locate sufficient free resources to utilize... (Code 12)"

Error Message in Its Entirety


This device can't seem to locate enough free resources to use. You must disable one of the other devices on this system to utilize this device. (code12)


The reason for the error code 12


If two devices installed on your computer have been given the same I/O ports, interrupt, or Direct Memory Access channel, this error might occur (either by the BIOS, the operating system, or both). If the BIOS does not provide adequate resources to the device, this error message will display.


Resolution Suggestions


Windows Vista and subsequent versions of the operating system


Determine the source of the problem and resolve it with Device Manager. See the Help section on how to use Device Manager for further information on how to resolve device conflicts. This error message can also display if a device's BIOS does not have enough resources allocated to it. For example, if the BIOS fails to assign an interrupt to a USB controller due to an incorrect multiprocessor specification (MPS) table, this error will appear.


Windows Server 2003, Windows XP, and Windows 2000 are all versions of Windows.


  1. Open the Device Manager program.
  2. In the Device Manager window, double-click the icon that represents the device.
  3. Click Troubleshoot on the device property sheet that displays to launch the hardware troubleshooter for the device.


This error message can also display if a device's BIOS does not have enough resources allocated to it. For example, if the BIOS fails to assign an interrupt to a USB controller due to an incorrect multiprocessor specification (MPS) table, this error will appear.


"This device will not function correctly till your computer is restarted." (code 14)


Error Message in Its Entirety


“Until you restart your computer, this device will not function correctly. Click Restart Computer (Code 14) to restart your computer right now.


Resolution Suggestions


Your computer should be restarted. Select Shut Down from the Start menu, then Restart.


“Windows is unable to determine all of the resources that this device employs.” (code 16)


Error Message in Its Entirety


“Windows is unable to recognize all of the resources that this device uses. Click the Resources tab and fill in the missing parameters to define extra resources for this device. To find out what settings to use, see your hardware manual. (Section 16)


The reason for the error code 16


The device is only partially set up, and more manual configuration of the device's resources may be necessary.


Resolution Suggestions


If the device is a Plug and Play device, the instructions below may only function. For further information, if the device is not Plug and Play, consult the device manual or contact the device maker.


  1. Search for device manager in Start and then pick Device Manager from the list of results.
  2. Select the Resources tab by double-clicking the device in the list.
  3. Check to see whether a resource has a question mark next to it in the Resource Settings list. If that's the case, go ahead and allocate that resource to the device.
  4. If you can't modify a resource, click Change Settings. If Change Settings is not accessible, clear the Use automatic settings check box to enable it.


Code 18 is a set of rules that governs "This device's drivers should be reinstalled. (code 18)"


Resolution Suggestions


Using the Hardware Update wizard, reinstall the device driver.


  1. Search for device manager in Start and then pick Device Manager from the list of results.
  2. Select the device from the list by right-clicking it.
  3. To begin the Hardware Update process, select Update Driver from the option that displays.


Manually reinstall the device driver


  1. Search for device manager in Start and then pick Device Manager from the list of results.
  2. Select the device from the list by right-clicking it.
  3. From the pop-up menu, choose Uninstall.
  4. Choose Action from the menu bar once the device has been uninstalled.
  5. To reinstall the driver, choose Scan for hardware changes.


Note You may be asked to provide the driver's path. If you don't have the driver and are asked for it, try downloading the most recent version from the hardware vendor's website.


Code 19 is a set of rules that governs "This hardware device cannot be started by Windows... (code 19)"

Error Message in Its Entirety


Because the configuration information (in the registry) for this hardware device is incomplete or corrupted, Windows is unable to start it. (Section 19)


The reason for the error code 19


When more than one service is specified for a device, the service key fails to open, or the driver name cannot be retrieved from the service key, this error occurs.


Resolution Suggestions


The driver should be uninstalled and reinstalled.


  1. Search for device manager in Start and then pick Device Manager from the list of results.
  2. Select the device from the list by right-clicking it.
  3. From the pop-up menu, choose Uninstall.
  4. Choose Action from the menu bar once the device has been uninstalled.
  5. To reinstall the driver, choose Scan for hardware changes.


Note: You may be asked to provide the driver's path. If you don't have the driver and are asked for it, try downloading the most recent version from the hardware vendor's website.


Reset the registry to its most recent successful configuration.


You may restore a system to the most recent successful registry configuration by restarting the computer in Safe Mode and selecting the Last Known Good Configuration option, or by restoring to a system restore point if one has been established.


"Windows is deleting this device...(Code 21)" says Code 21.


Error Message in Its Entirety


This device is being removed by Windows. (Section 21)


The reason for the error code 21


This error indicates that Windows is attempting to remove the device. The gadget, however, has not yet been removed fully. This is a transient error code that appears only when attempting to query and then delete a device.


Recommendations for Action


You may either restart the computer or wait for Windows to complete deleting the device.


  1. To refresh the Device Manager view, wait a few seconds and then press the F5 key.
  2. Restart your computer if it does not address the problem. To restart the machine, go to Start, Shut Down, and then Restart in the Shut Down Windows dialogue box.


"This device has been deactivated. (Code 22)"


Cause


In Device Manager, the user deactivated the device.


Resolution Suggestions


Click Action, and then Enable Device in Device Manager. The Enable Device wizard is launched as a result of this action. Observe the directions.


Code 24 is a code that is used to identify "This gadget is missing or isn't functioning correctly


Error Message in Its Entirety


This device is missing, isn't working, or doesn't have all of its drivers loaded. (code 24)


The reason for the error code 24


The gadget is improperly installed. It's possible that the issue is due to a hardware failure, or that a new driver is required. If devices have been readied for removal, they will remain in this state. This error goes away as you remove the gadget.


Resolution Suggestions


Remove the gadget, and the problem should go away.


Code 28 is a set of rules that governs "This device's drivers are not installed. (Section 28)"


Resolution Suggestions


Manually reinstall the device driver


  1. Search for device manager in Start and then pick Device Manager from the list of results.
  2. Select the device from the list by right-clicking it.
  3. From the pop-up menu, choose Uninstall.
  4. Choose Action from the menu bar once the device has been uninstalled.
  5. To reinstall the driver, choose Scan for hardware changes.


Note You may be asked to provide the driver's path. If you don't have the driver and are asked for it, try downloading the most recent version from the hardware vendor's website.


"This gadget has been disabled...(Code 29)"


Error Message in Its Entirety


This device is disabled because its firmware does not provide it with the resources it requires. (Section 29)


Resolution Suggestions


In the device's BIOS, enable the device. Consult the hardware manuals or contact the computer's maker for instructions on how to make this adjustment.


31 Is the code for "This gadget is malfunctioning...(Code 31)"


Error Message in Its Entirety


This device is not functioning correctly because Windows is unable to load the necessary drivers. (Section 31)


Resolution Suggestions


Using the Hardware Update wizard, reinstall the device driver.


  1. Search for device manager in Start and then pick Device Manager from the list of results.
  2. Select the device from the list by right-clicking it.
  3. To begin the Hardware Update process, select Update Driver from the option that displays.


Note: You may be asked to provide the driver's path. If you don't have the driver and are asked for it, try downloading the most recent version from the hardware vendor's website.


Code 32 is a kind of code that is used “This device's driver (service) has been deactivated. (code 32)


Error Message in Its Entirety


This device's driver (service) has been deactivated. This functionality might be provided by a different driver. (code 32)


The reason for the error code 32


In the registry, the start type for this driver is disabled.


Resolution Suggestions


Manually reinstall the device driver


  1. Search for device manager in Start and then pick Device Manager from the list of results.
  2. Select the device from the list by right-clicking it.
  3. From the pop-up menu, choose Uninstall.
  4. Choose Action from the menu bar once the device has been uninstalled.
  5. To reinstall the driver, choose Scan for hardware changes.


Note: You may be asked to provide the driver's path. If you don't have the driver and are asked for it, try downloading the most recent version from the hardware vendor's website.


Code 33 is a code that identifies “Windows is unable to identify which resources this device requires.


Cause


The translator that identifies what type of resources the gadget need has been broken down.


Recommendations for Action


  1. Update the BIOS or use the BIOS setup tool.
  2. Hardware can be configured, repaired, or replaced.


For additional information on upgrading your BIOS and configuring or replacing your device, contact the device's hardware provider.


Code 34 is a code that is used to identify “Windows is unable to determine this device's settings


Error Message in Its Entirety


This device's settings are unknown to Windows. To configure the configuration, consult the instructions that come with the device and utilize the Resource tab. (code 34)


Resolution Suggestions


The gadget must be configured manually. For details on manually setting the device, consult the product manuals or contact the hardware vendor. After you've configured the device, go to the Device Manager's Resources tab and change the resource settings in Windows.


The system firmware on your computer does not... (Code 35)”


Error Message in Its Entirety


The system firmware on your computer does not have enough information to fully configure and operate this device. To utilize this device, you'll need to get a firmware or BIOS update from your computer's maker. (code 35)


Cause


Your device's entry in the Multiprocessor System (MPS) table, which records resource allocations for the BIOS, is missing and needs to be replaced.


Resolution Suggestions


To update the BIOS on your computer, contact the manufacturer.


“This device is requesting a PCI interrupt... (Code 36)” says Code 36.


Error Message in Its Entirety


This device is asking for a PCI interrupt, yet it's set to an ISA interrupt (or vice versa). To change the interrupt for this device, use the computer's system setup software. (Section 36)


The reason for the error code 36


The translation of the interrupt request (IRQ) failed.


Resolution Suggestions


In the BIOS, change the IRQ reservations settings.


See the hardware manuals or contact the maker of your machine for additional information on how to alter BIOS settings. You may also try changing the IRQ reservations settings in the BIOS setup tool (if such options exist). Certain IRQs may be reserved for peripheral component interconnect (PCI) or ISA devices in the BIOS.


Code 37 is a kind of code that is used "The device driver for this hardware cannot be initialized by Windows. 


reason

When the DriverEntry function was run, the driver returned a failure.


Resolution Suggestions


Manually reinstall the device driver


  1. Search for device manager in Start and then pick Device Manager from the list of results.
  2. Select the device from the list by right-clicking it.
  3. From the pop-up menu, choose Uninstall.
  4. Choose Action from the menu bar once the device has been uninstalled.
  5. To reinstall the driver, choose Scan for hardware changes.


Note: You may be asked to provide the driver's path. If you don't have the driver and are asked for it, try downloading the most recent version from the hardware vendor's website.


“Windows cannot load the device driver... (Code 38)”


Error Message in Its Entirety


Because a previous instance of the device driver is still in memory, Windows is unable to load the device driver for this hardware. (code 38)


The reason for the error code 38


Because a previous instance is still loaded, the driver could not be loaded.


Resolution Suggestions


Your computer should be restarted. Select Shut Down from the Start menu, then Restart.


“Windows cannot load the device driver for this hardware... (Code 39)


Error Message in Its Entirety


The device driver for this hardware cannot be loaded by Windows. It's possible that the driver is corrupted or missing. (Section 39)


Resolution Suggestions


Manually reinstall the device driver


  1. Search for device manager in Start and then pick Device Manager from the list of results.
  2. Select the device from the list by right-clicking it.
  3. From the pop-up menu, choose Uninstall.
  4. Choose Action from the menu bar once the device has been uninstalled.
  5. To reinstall the driver, choose Scan for hardware changes.


Note: You may be asked to provide the driver's path. If you don't have the driver and are asked for it, try downloading the most recent version from the hardware vendor's website.


“Windows cannot access this hardware... (Code 40)


Error Message in Its Entirety


Because the service key information in the registry is missing or improperly stored, Windows is unable to access this device. (code 40)


Cause


The driver's information in the registry's service subkey is incorrect.


Resolution Suggestions


Manually reinstall the device driver


  1. Search for device manager in Start and then pick Device Manager from the list of results.
  2. Select the device from the list by right-clicking it.
  3. From the pop-up menu, choose Uninstall.
  4. Choose Action from the menu bar once the device has been uninstalled.
  5. To reinstall the driver, choose Scan for hardware changes.


Note: You may be asked to provide the driver's path. If you don't have the driver and are asked for it, try downloading the most recent version from the hardware vendor's website.


“Windows successfully loaded the device driver (code 41)


Error Message in Its Entirety


The device driver for this hardware was successfully loaded by Windows, but the physical device could not be found. (Section 41)


The reason for the error code 41


If you install a driver for a device that isn't Plug and Play, but Windows can't detect it, you'll get this error.


Resolution Suggestions


Manually reinstall the device driver


  1. Search for device manager in Start and then pick Device Manager from the list of results.
  2. Select the device from the list by right-clicking it.
  3. From the pop-up menu, choose Uninstall.
  4. Choose Action from the menu bar once the device has been uninstalled.
  5. To reinstall the driver, choose Scan for hardware changes.


Note: You may be asked to provide the driver's path. If you don't have the driver and are asked for it, try downloading the most recent version from the hardware vendor's website.


“Windows cannot load the device driver... (Code 42)” says the error message.


Error Message in Its Entirety


Because a duplicate device is already functioning in the system, Windows is unable to load the device driver for this hardware. (Section 42)


The reason for the error code 42


A duplicate gadget has been discovered. When a bus driver produces two identically named sub-processes (a bus driver mistake) or when a device with a serial number is detected in a new place before it is deleted from the old location, this error occurs.


Resolution Suggestions


Your computer should be restarted. Select Shut Down from the Start menu, then Restart.


Code 43 is a code that is used to identify "This device has been disabled by Windows because it has reported issues.


The reason for the error code 43

One of the device's drivers alerted the operating system that the device had failed in some way.


Resolution Suggestions


Check the hardware documentation or contact the manufacturer for further information about identifying the problem if you've already tried the "Try these steps first" section.


Manually reinstall the device driver


  1. Search for device manager in Start and then pick Device Manager from the list of results.
  2. Select the device from the list by right-clicking it.
  3. From the pop-up menu, choose Uninstall.
  4. Choose Action from the menu bar once the device has been uninstalled.
  5. To reinstall the driver, choose Scan for hardware changes.


Note: You may be asked to provide the driver's path. If you don't have the driver and are asked for it, try downloading the most recent version from the hardware vendor's website.


Code 44 is a code that identifies “This hardware device has been turned off by an application or service. (Code 44)”


Resolution Suggestions


Your computer should be restarted. Select Shut Down from the Start menu, then Restart.



45 is the code for “This hardware device is currently disconnected from the computer... (Code 45)”


Error Message in Its Entirety


This hardware item is not currently connected to the computer. Reconnect this hardware item to the computer to resolve the issue. (code 45)


The reason for the error code 45


If a device that was previously connected to the computer is no longer connected, this error will appear. Connect this hardware item to the computer to fix the problem.


Resolution Suggestions


There is no need for a resolution. This error number is solely used to signal that the device is unplugged and does not need to be fixed. When you connect the connected device to the computer, the error code disappears.



Code 46 is a code that is used to identify “Windows is unable to access this hardware devic


Error Message in Its Entirety


Because the operating system is in the process of shutting down, Windows is unable to access this physical device. When you restart your computer, the hardware device should operate properly. (code 46)


The reason for the error code 46


Because the system is shutting down, the gadget is unavailable.


Resolution Suggestions


There is no need for a resolution. The hardware device should function properly the next time you turn on the computer. When Driver Verifier is activated and all programs have been closed, this error code is generated.



Windows cannot use this hardware devic (code 47)


Error Message in Its Entirety


This hardware device cannot be used by Windows because it has been readied for safe removal but has not been removed from the computer. Unplug this device from your computer and then re-plug it to resolve the issue. (Section 47)


The reason for the error code 47


This error code appears only if you utilized the Safe Removal program or hit a physical eject button to prepare the device for removal.


Resolution Suggestions


Remove the device from the computer and reconnect it. If it doesn't fix the problem, restart your computer. Select Shut Down from the Start menu, then Restart.


Code 48 is a set of rules that governs “This device's software has been disabled... (Code 48).”


Error Message in Its Entirety


This device's software has been disabled because it has been known to create issues with Windows. For a new driver, contact the hardware manufacturer. (Section 48)


Resolution Suggestions


To acquire the most recent version or an updated driver, contact the manufacturer of your hardware device. Then, on your computer, install it.


Code 49 is a set of rules that governs “Windows is unable to start new hardware device


Error Message in Its Entirety


Because the system hive is too huge, Windows is unable to start new hardware devices (exceeds the Registry Size Limit). (code 49)


The reason for the error code 49


The system hive has reached its maximum capacity, and additional devices will not be able to function until the capacity is decreased. The system hive is a component of the registry that is permanently linked to a group of files that hold information about the configuration of the computer on which the operating system is installed. Applications, user preferences, devices, and other objects may all be configured. Specific devices that are no longer linked to the computer but are still mentioned in the system hive might be the source of the problem.


Resolution Suggestions


Remove any hardware devices that are no longer in use.


  • Device Manager may be configured to display devices that are no longer connected to the computer.


  1. Click Run from the Start menu.
  2. Type cmd in the Open box. The window for the Command Prompt appears.
  3. Type the following command at the prompt, then click Enter: set devmgr show nonpresent devices=1 devmgr show nonpresent devices=1


  • Click View, and then Show Hidden Devices in Device Manager. Devices that are not connected to the computer will now be shown.
  • Choose a device that isn't currently connected. Select Uninstall from the Driver tab.
  • Step 3 should be repeated for any non-present devices that are no longer in use. Restart your PC after that.
  • In Device Manager, check the device Properties dialogue box to verify if the error has been fixed.


"Windows is unable to apply all of this device's properties... (Code 50)"


Error Message in Its Entirety


Windows is unable to apply all of the device's attributes. Information about the device's capabilities and settings may be included in its properties (such as security settings for example). You can try reinstalling this device to solve the problem. However, if you need a new driver, we recommend contacting the hardware manufacturer. (Code50)


Resolution Suggestions


Manually reinstall the device driver


  1. Search for device manager in Start and then pick Device Manager from the list of results.
  2. Select the device from the list by right-clicking it.
  3. From the pop-up menu, choose Uninstall.
  4. Choose Action from the menu bar once the device has been uninstalled.
  5. To reinstall the driver, choose Scan for hardware changes.


Note: You may be asked to provide the driver's path. If you don't have the driver and are asked for it, try downloading the most recent version from the hardware vendor's website.


Code 51 is a code that is used to identify "This device is now awaiting the arrival of another device... (Code 51)"


Error Message in Its Entirety


This device is presently awaiting the commencement of another device or group of devices. (Section 51)


Resolution Suggestions


Currently, there is no remedy to this issue. Examine other failed devices in the device tree that this device may rely on to help determine the problem. You might be able to remedy this problem if you can figure out why another connected device failed to start.


52 is a code that refers to a “Windows is unable to validate the digital signature for the device's drivers. (code 52)


Error Message in Its Entirety


The digital signature for the drivers required for this device cannot be verified by Windows. A recent hardware or software upgrade may have installed a file that is improperly signed or corrupted or dangerous malware from an unknown source. (code 52)


The reason for the error code 52


It's possible that the driver is unsigned or corrupted.


Resolution Suggestions


Obtain the most recent driver from the hardware manufacturer's website, or contact them for assistance.


a code of 53 “The Windows kernel debugger has been assigned to this device... (Code 53)”


Error Message in Its Entirety


For the duration of this boot session, this device has been set aside for usage by the Windows kernel debugger. (Section 53)


Resolution Suggestions


To allow the device to start properly, disable Windows kernel debugging.


54 is a code. “This device has malfunctioned and is being reset. (Code 54)”


The reason for the error code 54

This is an issue code that appears on occasion when an ACPI reset technique is used. The device will be trapped in this state if it never restarts due to a failure, and the system will need to be restarted.


Resolution Suggestions


Your computer should be restarted. Select Shut Down from the Start menu, then Restart. free driver updater

No comments:

Powered by Blogger.